Ahtna Global

Summary:

This position will report to the corresponding Project Superintendent or designee. This position will require someone with the ability to lead construction crews on smaller projects and will be required to work hands-on with the crew at times. Perform tasks involving physical labor indoors and outdoors, including moving material, equipment, and parts between production areas; operating hand/power tools of all types, including air hammers; surveying and measuring equipment; and various other equipment and instruments. May clean and prepare sites, dig trenches, set braces to support the sides of excavations, erect scaffolding, and clean up rubble and debris. May assist other craft workers.

The pay rate for this position is $24.00-$30.00/hour.

This position is located in Guam.

Essential Duties and Responsibilities: (including but not limited to)

• Finish carpentry work at a journeyman level
• Ability to lay out a project mathematically.
• General knowledge and ability to perform other disciplines such as painting, plumbing, electrical, excavation, sheetrock installation, and finishing.
• Assist and coordinate with the team to manage field personnel to complete tasks on time and within budget.
• Examine and inspect work progress and equipment on construction and environmental project sites to verify safety and to ensure that specifications are met.
• Estimate materials and worker requirements to complete jobs.
• Order or requisition materials and supplies as needed.
• Schedule and supervise subcontractors.
• Layout - Locate, measure, and mark site locations and placement of structures and equipment using measuring and marking equipment.
• Signal equipment operators to facilitate alignment, movement, and adjustment of machinery, equipment, and materials.
• Spray materials such as water, sand, steam, vinyl, paint, or stucco through hoses to clean, coat, or seal surfaces.
• Tend machines that pump concrete, grout, cement, sand, plaster, or stucco through spray guns for application to ceilings and walls.
• Tend pumps, compressors, and generators to provide power for tools, machinery, and equipment or to heat and move materials such as asphalt.
• Lubricate, clean, and repair machinery, equipment, and tools.
• Build and position forms for pouring concrete and dismantle forms after use using saws, hammers, nails, or bolts.
• Clean and prepare construction sites to eliminate possible hazards.
• Control traffic passing near, in, and around work zones.
• Dig ditches/trenches, backfill excavations, and compact/level earth-to-grade specifications using picks, shovels, pneumatic tampers, and rakes.
• Erect and disassemble scaffolding, shoring, braces, traffic barricades, ramps, and other temporary structures.
• Load, unload, and identify building materials, machinery, and tools and distribute them to the appropriate locations according to project plans/specifications.
• Measure, mark, and record openings and distances where construction work will be performed.
• Raze buildings and salvage useful materials.
• Demo various Architectural finishes, such as, but not limited to, carpeting, ceiling tile, drywall, etc.
• Patch, repair, and install various Architectural finishes, such as carpeting, ceiling tile, drywall, etc.
• May supervise or escort other workers or subcontractors and ensure that safe work practices are constantly employed.
• Read and interpret plans, instructions, and specifications to determine work activities.
• Perform any other duties as assigned by management.

Minimum Qualifications

• High School Graduate or General Education Degree (GED)
• Ten (10) years of experience as a Carpenter
  • Three (3) years of experience at the foreman level
• Knowledge of construction machines and tools, including their designs, uses, repair and maintenance, and the practical application of use
• Valid Driver’s license with the ability to be covered under company vehicle policy and the ability to travel to local facilities
• Ability to pass background checks by various Federal Agencies (e.g., DOD, DHS, FAA, etc.) to obtain security access badges
• Some positions may require U.S. Citizenship

Preferred Qualifications

• Technical school in the art of carpentry
• OSHA 10 Training Certificate preferred
• Knowledge and experience with Alaska Native cultures

Shareholder Preference:

Pursuant to applicable law, preference will be given to qualified Ahtna Native Corporation Shareholders, Descendents, and Spouses in all phases of employment.

Core Competencies:

• Self-motivated - Ability to be internally inspired to perform a task to the best of one’s ability using his or her own drive or initiative.
• Communication - Ability to communicate effectively with others using the spoken and written word.
• Time Management - Ability to utilize the available time to organize and complete work within given deadlines.

Working Environment:

• May be indoors or outdoors, subject to confined spaces, changes in temperature, weather conditions, and noise levels.

Physical Demands (including but not limited to):

• Frequent lifting, sitting, standing, stooping for prolonged periods of time, using hands/fingers requiring dexterity, should have good hand-eye coordination and motion control in coordination with handling tools, equipment, and other related components.
• Reaching with hands and arms for items above and below sight level, talking, hearing, and seeing (up close, at a distance, along the periphery, with depth, color perception, and the ability to adjust focus); walking from place to place within the project location with occasional use of stairs and no elevator available; bending, pushing, pulling, and standing for up to 12 hours.
• Frequent lifting of up to 50 pounds, such as small electrical components, equipment, and other materials.

Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

Work Schedule: Varies as business/operational needs dictate